Dynamix DW 2 FXO Manual de usuario

DYNAMIX DW-0002 DYNAMIX DW-0004 DYNAMIX DW-0006 FXO Gatewey User Manual (2/4/6 ports)

Gatekeeper when it is set as Gatekeeper Mode. 3. Or when FXO GateWay is in downloading mode, LED should be flash as well. 4. Light off means

w Please wait a moment... Write flash ok... Boot Rom : boot.104 Application Rom : 3804_0701.bin DSP App : 48302ce3

The Procedures of recording the disconnect tone Before you start  Two PSTN lines which connected with the Line 1 and Line 2 port. Configure Peer-

... ...

frequency low : 480 frequency high level : 8 frequency low level : 8 Tone1 on : 50 Tone1 off

Frequency 1 : 473 Frequency 2 (2623) is more than 1000, please ignore it. 0. 25sec on 0.25sec off tone 4 473 473 8 8 25 25 1023 1023 (Please confi

Tone2 off : 1023 Disconnect tone 4 paramter Frequency high : 473 frequency low : 473 frequency high level

Example: ddns -print ddns -enable 1 ddns -server member.dyndns.org -hostname ipphone.dyndns.org ddns -delay 30 m (30 minutes)

-faxbypass Configurate the FAX ByPass payload type. -modembypass Configurate the MODEM ByPass payload type. -redundancy Configurate

'dspapp', and 'rbpcm'. Example: rom -method 1 rom -ftp vwusr vwusr rom -app -s 192.168.4.101 -f app.bin Pa

TFTP, while “1” stands for FTP. -ftp if users choose FTP in above item, it is necessary to specify pre-defined username and password when upgrading

LED should be flash as well. 4. Light off means Dynamix DW-0006/H is in Peer-to-Peer Mode. Back panel: 1. Ethernet Port LAN/WAN: 10/100 Base-T; R

STEPS IN CONFIGURATION ...3 1. START UP ...

3.15 VERSION AND INFORMATION ...51 3.14 ROM UPGRADE ...

4.2.23 [rom] ...105 4.2.24 [passwd] command ...

Steps in configuration To check out the peripheral equipments and understand the feature of this gateway. Please read this step very carefully befo

1. Start Up 1.1 Introduction The FXO gateway provides voice/fax service over IP network with H.323 v3 protocol. By connecting to your existing ADSL

1.2 Features and specification Features - ITU-T H.323 v4 compliance - Automatically Gatekeeper Discovery - Secondary GK support - Peer-to-Peer m

Management Features: Two easy ways for system configuration - Console port: RS-232C port - TELNET - HTTP Brower (e.g. Internet Explorer) 1.3 Acces

registered to Gatekeeper when it is set as Gatekeeper Mode. 2. LED flash means Dynamix DW-0002/H is not registered to Gatekeeper when it is set as G

Gatekeeper when it is set as Gatekeeper Mode. 3. Or when FXO GateWay is in downloading mode, LED should be flash as well. 4. Light off means

LED should be flash as well. 4. Light off means Dynamix DW-0006/H is in Peer-to-Peer Mode. Back panel: 1. Ethernet Port LAN/WAN: 10/100 Base-T; R

Pin Name Dir Description 2 RXD Receive Data 3 TXD Transmit Data 5 GND System Ground 3. TEL: RJ-11 connector, FXS interface is for connecting th

Pin Name Dir Description 2 RXD Receive Data 3 TXD Transmit Data 5 GND System Ground 3. TEL: RJ-11 connector, FXS interface is for connecting th

2. How to Setup and connect basically 2.1 System Requirement 1. One PC (a) Pentium 100 or above, 64 RAM, Windows 98 or above. (b) Ethernet card or C

2.2 IP Environment Setting User must prepare a valid IP address, complied with IP Network, for Gateway’s proper operation. For testing the validati

3 Select the Property of the LAN card. 4 Setup the ip address, subnet mask and default gateway as below: Figure 2.2: Configure the network 5 Click O

2.3 Network configurations in your gateway 1 Key in the ip address of the gateway (http://10.1.1.3) with the browser Figure 2.3: WEB Browser 2 Afte

Figure 2.3: Login the username and password 3 You will enter the main page of the configuration after key in the login name and password correctly:

2.3.1 Static ip address 1 Please get the correct ip address, netmask and default gateway address from your ISP first. Press the OK button if you fin

3 Press the reboot if you want the configuration executed. Figure 2.7: Reboot the system 2.3.2 DHCP mode 1 Enable the DHCP if you are using the ca

2 Please commit the data and reboot the machine after you enable the DHCP function. 2.3.3 PPPoE mode 1 Enable the PPPoE and press the info about PP

Figure 2.10: Configure the info about PPPoE 2 Please commit the data and reboot the machine after you finished the configuration of PPPoE. 2.4 Mak

2. How to Setup and connect basically 2.1 System Requirement 1. One PC (a) Pentium 100 or above, 64 RAM, Windows 98 or above. (b) Ethernet card or C

Figure 2.11: Configure the Peer-to-Peer mode 2 Press the OK button that is on the bottom of this page to save the configuration. Figure 2.12: The O

Figure 2.11: Phone Book Example Figure 2.12: The example of Phone Book configuration This is the first record of Phone Book. So the index is 1 T

4 Press the “Add Data” button when you finished, and the new table will display on the first index if you press the Phone Book configuration button.

Figure 2.14: Configure the GK info 2 Press the OK button that is on the bottom of this page to save the configuration. Figure 2.15: Press OK to sav

2.4.2.1 The type in GK routed mode There are two types in the GK routed mode you could choose. One is Gateway type and another is Terminal type. The

3. Advance Configurations There are too many advanced commands for the advanced users. The following chapters are based on the application layer. Pl

gain a valid one.  Another IP Address for Gateway must be set as an fixed one in order for that IP Sharing device pass forwarding the relevant infor

Figure 3.2: Enable the ip sharing function 3 The IP change function is only for the special usage Figure 3.3: IP Change  IP Change Function:

change is only support the GK from us. 4 Please Commit it and Reboot the system if the configuration is finished. This chapter is focus on the DM

3.2 Network Interface Users have to configure the Network configurations in this page. This gateway will be work while it is connecting with the inte

2.2 IP Environment Setting User must prepare a valid IP address, complied with IP Network, for Gateway’s proper operation. For testing the validati

remote side.  SNTP – Enable the SNTP server registering function if user wants to get the correct time from the Command Line Interface.  SNTP Serve

3.3 H323 Information This WEB page will help user to configure the information about the dial mode, GK information and some TCP/IP port for the commu

 Line 2 / LINE1 Number – Configure the number of the second port in this unit.  Line 3 / TEL 2 Number – Configure the number of the third port in t

destination unit. Support the GK mode only.  Allocate Port Range Start – To configure the beginning of the ports.  Allocate Port Range End – To con

3.4 Line Configuration The Line configuration will show the status of the registrations and the ports. It includes the hunt group, hotline, and no an

3.5 Phone Book Configuration The Phone Book configuration is only support the gateway in Peer-to-Peer mode. Please refer the chapter 2 about the Peer

 Delete Date – If users want to delete the record from the table, enter the index number first and press this button. The record will be deleted.

3.6 Support Configuration This gateway support the FAX over IP, fast start function and others function. Please enable or disable these in the Suppor

3.7 System Configuration Figure 3.9: System Configuration  Inter Digit Time – The call will be sent out if user didn’t enter the digits after this

 Master : Follow the result from the MasterSlaveDetermination.  Caller : Follow the caller side. It’s only for the special requirement. Please c

3 Select the Property of the LAN card. 4 Setup the ip address, subnet mask and default gateway as below: Figure 2.2: Configure the network 5 Click O

 Force 2nd dial : Every calls will need the 2nd stage dialing type.  Hardware Type – This will show the hardware detection type. Support the FXS/F

3.8 Voice Configuration Users could configure the voice codec or gain level in this web page. Please get more detail info from the following descript

(input) and DTMF gain (DTMF) of the second FXO port.  Line6 Volume – To configure the output gain (voice), input gain (input) and DTMF gain (DTMF) o

3.9 Phone Configuration This WEB will show the tone generation value from this unit. Please don’t configure it if you got some correct value for sure

3.10 RTP Pay Load Type Configuration There are more types for the RTP Payload. This web page could support users define the Payload Type for some spe

3.11 IP Packet ToS The Type of Service should be worked with the network router. The router will check all the packets if it support the TOS function

3.12 DDNS Configuration This version of firmware supports DDNS function. Before using this function, please have a DDNS account and some info from yo

3.13 Prefix Configuration The Prefix function is using the drop and insert function (see figure 3.15). Figure 3.15: Prefix Configuration  Index –

1 Press the Prefix Configuration button to enter the configuration table (see figure 3.15) 2 Enter the index number. Put the prefix numbers you will

3 Press the Prefix Configuration button to reload the configuration table (see figure 3.17) Figure 3.17: Configure the Prefix Table 4 Please Commit

2.3 Network configurations in your gateway 1 Key in the ip address of the gateway (http://10.1.1.3) with the browser Figure 2.3: WEB Browser 2 Afte

3.14 Password Configuration There are two-login accounts in this unit. One is the account root another is administrator. The default setting for thes

3.15 Version and Information Users could get more detail about the software version for all the parts in this web page. (see figure 3.19) Figure 3.

3.14 ROM Upgrade User could update the firmware just by the web configuration interface. There are two types for the upgrading procedure. One is usin

Updating the firmware by the FTP server 1 Pick up the “Rom Upgrade” button to enter the upgrading web page and switch to the FTP method. (see figu

Figure 3.21: FTP information 3 Press the OK button to start the upgrade procedure. 4 Please follow the direction on the web site if the download pr

Figure 3.23: TFTP information 4 Press the OK button to start the upgrade procedure. Please pay more attentions on the file name you used. The file

3.20 Flash Clean Users could make all the configurations back to the default setting by this button. The password of the account and the networking c

3.21 Commit Users could configure the information for the PPPoE connection in this page. After the configurations, the gateway will try to connect th

3.22 Reboot System This web page will restart the whole system. This is the necessary step for the changing the configurations and makes it executed.

3.23 Tone Configuration Users could configure the tone pattern of the gateway in this page. If the disconnect tone from PSTN side is match the one of

Figure 2.3: Login the username and password 3 You will enter the main page of the configuration after key in the login name and password correctly:

3.24 Routing Table Routing Table is a rule to define the destination of the calls you make. You could define the rules by the number you dial or by t

route table if the prefix number was matched.  Destination – To decide the destination for this route table.  E.164 – The E.164 number of the desti

Figure 3.29: Change The Default Setting 2 The default setting is changed after you press the Change Default button. Please press the Routing Table b

3.24.2 Add a new Routing Table 1 The default setting is changed after you press the Change Default button. Please press the Routing Table button agai

The explanation of figure 3.32 is as below: When the user dial 8 with the first digit of the numbers from FXO or IP side. And the numbers you dial i

3.25 FXO Password You will get the IVR if you make calls from PSTN side or from IP side. The IVR will ask you the password you set, and you could mak

4. Command List 4.1 Hyper Terminal Setting A terminal emulator is needed when using RS-232 port to configure Gateway. There are kinds of terminal em

Figure 4.2: Edit the name of the connection 3. After pressing OK button, the next window appear, and then choose COM1/2 Port, which you are going

Figure 4.4: Configure the right Bps and control 5. Press ‘OK’ button, and then start to configure Gateway. 68

4.2 Command List 4.2.1 [help] Type help or man or ? to list all the available command. usr/config$ ? help help/man/? [command] quit quit/exit/cl

2.3.1 Static ip address 1 Please get the correct ip address, netmask and default gateway address from your ISP first. Press the OK button if you fin

to login prompt. usr/config$ quit Disconnecting... login: Note: It is recommended that type the “quit” command before you leave the console. If so

4.2.4 [reboot] After commit command, type reboot to reload FXO GateWay in new configuration. The procedure is as below: usr/config$ reboot Attached

4.2.6 [commit] Save changes after configuring the FXO GateWay. -----------------------------------------------------------------------------------

-id PPPoE connection user name -pwd PPPoE connection password -reboot Reboot after remote host disconnection in PPPoE mode

usr/config$ ifaddr -sntp 1 10.1.1.1 While 10.1.1.1 stands for SNTP server’s IP address. -ipchange If the unit is behind the IP sharing device

PING 210.54.23.129: 56 data bytes no answer from 210.54.23.129 usr/config$ ping 192.168.4.121 PING 192.168.4.121: 56 data bytes 64 bytes from 192.168

-gwprefix Drop gateway prefix when call from IP (0=Keep, 1=Drop). -eod End of dial (0=Disable, 1=Enable). -ring T

level to determine who is master.) -gwprefix drop or keep gateway prefix . “0” means when gateway has incoming call from IP side, it will not drop p

4.2.11 [h323] Phone Book function allows users to define their own numbers, which mapping to real IP address. It is effective only in peer-to-peer m

-gkfind Gatekeeper finding port (1024~65535). -gkras Gatekeeper RAS port (1024~65535). -h225 H225 ras port (1024~65535).

3 Press the reboot if you want the configuration executed. Figure 2.7: Reboot the system 2.3.2 DHCP mode 1 Enable the DHCP if you are using the ca

define [prefix] in next command. Terminal type – device will register as H.323 defined Terminal, [prefix] command is not necessary. -dfgw default

this to recognize the called party. -gkid set GateKeeper name for GateKeeper discovery. When Gateway send out GateKeeper discovery message will sear

line -print Gateway line information. -config Set Gateway line information. hunt: Hunting group. hotline

automatically dial out “1001”. P2P Mode Usage: Set gateway under P2P mode. Create phone book table with “pbook ” command. Create a Hotline table wit

prefix -print prefix -add prefix 100 drop 1 insert 2000 prefix -add prefix 100 drop 1 prefix -add prefix 100 drop 0 ins

[-delete number] pbook -print Display phone book information and configuration. -add Add new phone book record.

sequence number as index. -add add a new record to phone book. When adding a record, users have to specify name, ip, and e164 number to complete th

[-volume line [voice level][input level][dtmf level]] [-nscng [G711U used1][G711A used2][G723 used3]] [-echo used][-mindelay t1][-

-print print current voice information and configurations. -send define packet size for each codec. 20/40/60ms means to send a voice packet per 20/

usr/config$ voice –mindelay 90 –maxdelay 150 Note: be sure to know well the application before you change voice parameters because this might caus

STEPS IN CONFIGURATION ...3 1. START UP ...

2 Please commit the data and reboot the machine after you enable the DHCP function. 2.3.3 PPPoE mode 1 Enable the PPPoE and press the info about PP

Parameter Usages: -print print current settings in support command. -t38 to switch ON/OFF (1 = ON; 0 = OFF) T.38 fax ability. When T.38 ability is

=========================== 1 OK Ready 2 OK Ready 3 OK Ready 4 OK Ready usr/config$ 4.2.18 [

-ip Change the IP default rule.(1=FXO, 2=IP) -fxo Change the FXO default rule.(1=FXO, 2=IP) Example: route -add prefix

is to hunt between all ports in the same type. Usage Example: 1. route –add prefix 100 dst 1 e164 1001 min 1 max 3 hunt 1 This command means if gat

Tone1OFF . Tone2ON . Tone2OFF . Example: tone -print tone 1 480 620 1 1 5

[-modify index [passwd number][direction number]] [-delete index] fxopwd -print Display FXO password information and configurat

calling in FXO line of Gateway. ----------------------------------------------------------------------------------------------- usr/config$ recor

Please wait a moment... Write flash ok... Boot Rom : boot.104 Application Rom : 3804_0701.bin DSP App : 48302ce3.

w Please wait a moment... Write flash ok... Boot Rom : boot.104 Application Rom : 3804_0701.bin DSP App : 48302ce3

The Procedures of recording the disconnect tone Before you start  Two PSTN lines which connected with the Line 1 and Line 2 port. Configure Peer-

Figure 2.10: Configure the info about PPPoE 2 Please commit the data and reboot the machine after you finished the configuration of PPPoE. 2.4 Mak

... ...

frequency low : 480 frequency high level : 8 frequency low level : 8 Tone1 on : 50 Tone1 off

Frequency 1 : 473 Frequency 2 (2623) is more than 1000, please ignore it. 0. 25sec on 0.25sec off tone 4 473 473 8 8 25 25 1023 1023 (Please confi

Tone2 off : 1023 Disconnect tone 4 paramter Frequency high : 473 frequency low : 473 frequency high level

Example: ddns -print ddns -enable 1 ddns -server member.dyndns.org -hostname ipphone.dyndns.org ddns -delay 30 m (30 minutes)

-faxbypass Configurate the FAX ByPass payload type. -modembypass Configurate the MODEM ByPass payload type. -redundancy Configurate

'dspapp', and 'rbpcm'. Example: rom -method 1 rom -ftp vwusr vwusr rom -app -s 192.168.4.101 -f app.bin Pa

TFTP, while “1” stands for FTP. -ftp if users choose FTP in above item, it is necessary to specify pre-defined username and password when upgrading

Figure 2.11: Configure the Peer-to-Peer mode 2 Press the OK button that is on the bottom of this page to save the configuration. Figure 2.12: The O

Figure 2.11: Phone Book Example Figure 2.12: The example of Phone Book configuration This is the first record of Phone Book. So the index is 1 T

4 Press the “Add Data” button when you finished, and the new table will display on the first index if you press the Phone Book configuration button.

Figure 2.14: Configure the GK info 2 Press the OK button that is on the bottom of this page to save the configuration. Figure 2.15: Press OK to sav

2.4.2.1 The type in GK routed mode There are two types in the GK routed mode you could choose. One is Gateway type and another is Terminal type. The

3. Advance Configurations There are too many advanced commands for the advanced users. The following chapters are based on the application layer. Pl

gain a valid one.  Another IP Address for Gateway must be set as an fixed one in order for that IP Sharing device pass forwarding the relevant infor

Figure 3.2: Enable the ip sharing function 3 The IP change function is only for the special usage Figure 3.3: IP Change  IP Change Function:

3.15 VERSION AND INFORMATION ...51 3.14 ROM UPGRADE ...

change is only support the GK from us. 4 Please Commit it and Reboot the system if the configuration is finished. This chapter is focus on the DM

3.2 Network Interface Users have to configure the Network configurations in this page. This gateway will be work while it is connecting with the inte

remote side.  SNTP – Enable the SNTP server registering function if user wants to get the correct time from the Command Line Interface.  SNTP Serve

3.3 H323 Information This WEB page will help user to configure the information about the dial mode, GK information and some TCP/IP port for the commu

 Line 2 / LINE1 Number – Configure the number of the second port in this unit.  Line 3 / TEL 2 Number – Configure the number of the third port in t

destination unit. Support the GK mode only.  Allocate Port Range Start – To configure the beginning of the ports.  Allocate Port Range End – To con

3.4 Line Configuration The Line configuration will show the status of the registrations and the ports. It includes the hunt group, hotline, and no an

3.5 Phone Book Configuration The Phone Book configuration is only support the gateway in Peer-to-Peer mode. Please refer the chapter 2 about the Peer

 Delete Date – If users want to delete the record from the table, enter the index number first and press this button. The record will be deleted.

3.6 Support Configuration This gateway support the FAX over IP, fast start function and others function. Please enable or disable these in the Suppor

4.2.23 [rom] ...105 4.2.24 [passwd] command ...

3.7 System Configuration Figure 3.9: System Configuration  Inter Digit Time – The call will be sent out if user didn’t enter the digits after this

 Master : Follow the result from the MasterSlaveDetermination.  Caller : Follow the caller side. It’s only for the special requirement. Please c

 Force 2nd dial : Every calls will need the 2nd stage dialing type.  Hardware Type – This will show the hardware detection type. Support the FXS/F

3.8 Voice Configuration Users could configure the voice codec or gain level in this web page. Please get more detail info from the following descript

(input) and DTMF gain (DTMF) of the second FXO port.  Line6 Volume – To configure the output gain (voice), input gain (input) and DTMF gain (DTMF) o

3.9 Phone Configuration This WEB will show the tone generation value from this unit. Please don’t configure it if you got some correct value for sure

3.10 RTP Pay Load Type Configuration There are more types for the RTP Payload. This web page could support users define the Payload Type for some spe

3.11 IP Packet ToS The Type of Service should be worked with the network router. The router will check all the packets if it support the TOS function

3.12 DDNS Configuration This version of firmware supports DDNS function. Before using this function, please have a DDNS account and some info from yo

3.13 Prefix Configuration The Prefix function is using the drop and insert function (see figure 3.15). Figure 3.15: Prefix Configuration  Index –

Steps in configuration To check out the peripheral equipments and understand the feature of this gateway. Please read this step very carefully befo

1 Press the Prefix Configuration button to enter the configuration table (see figure 3.15) 2 Enter the index number. Put the prefix numbers you will

3 Press the Prefix Configuration button to reload the configuration table (see figure 3.17) Figure 3.17: Configure the Prefix Table 4 Please Commit

3.14 Password Configuration There are two-login accounts in this unit. One is the account root another is administrator. The default setting for thes

3.15 Version and Information Users could get more detail about the software version for all the parts in this web page. (see figure 3.19) Figure 3.

3.14 ROM Upgrade User could update the firmware just by the web configuration interface. There are two types for the upgrading procedure. One is usin

Updating the firmware by the FTP server 1 Pick up the “Rom Upgrade” button to enter the upgrading web page and switch to the FTP method. (see figu

Figure 3.21: FTP information 3 Press the OK button to start the upgrade procedure. 4 Please follow the direction on the web site if the download pr

Figure 3.23: TFTP information 4 Press the OK button to start the upgrade procedure. Please pay more attentions on the file name you used. The file

3.20 Flash Clean Users could make all the configurations back to the default setting by this button. The password of the account and the networking c

3.21 Commit Users could configure the information for the PPPoE connection in this page. After the configurations, the gateway will try to connect th

1. Start Up 1.1 Introduction The FXO gateway provides voice/fax service over IP network with H.323 v3 protocol. By connecting to your existing ADSL

3.22 Reboot System This web page will restart the whole system. This is the necessary step for the changing the configurations and makes it executed.

3.23 Tone Configuration Users could configure the tone pattern of the gateway in this page. If the disconnect tone from PSTN side is match the one of

3.24 Routing Table Routing Table is a rule to define the destination of the calls you make. You could define the rules by the number you dial or by t

route table if the prefix number was matched.  Destination – To decide the destination for this route table.  E.164 – The E.164 number of the desti

Figure 3.29: Change The Default Setting 2 The default setting is changed after you press the Change Default button. Please press the Routing Table b

3.24.2 Add a new Routing Table 1 The default setting is changed after you press the Change Default button. Please press the Routing Table button agai

The explanation of figure 3.32 is as below: When the user dial 8 with the first digit of the numbers from FXO or IP side. And the numbers you dial i

3.25 FXO Password You will get the IVR if you make calls from PSTN side or from IP side. The IVR will ask you the password you set, and you could mak

4. Command List 4.1 Hyper Terminal Setting A terminal emulator is needed when using RS-232 port to configure Gateway. There are kinds of terminal em

Figure 4.2: Edit the name of the connection 3. After pressing OK button, the next window appear, and then choose COM1/2 Port, which you are going

1.2 Features and specification Features - ITU-T H.323 v4 compliance - Automatically Gatekeeper Discovery - Secondary GK support - Peer-to-Peer m

Figure 4.4: Configure the right Bps and control 5. Press ‘OK’ button, and then start to configure Gateway. 68

4.2 Command List 4.2.1 [help] Type help or man or ? to list all the available command. usr/config$ ? help help/man/? [command] quit quit/exit/cl

to login prompt. usr/config$ quit Disconnecting... login: Note: It is recommended that type the “quit” command before you leave the console. If so

4.2.4 [reboot] After commit command, type reboot to reload FXO GateWay in new configuration. The procedure is as below: usr/config$ reboot Attached

4.2.6 [commit] Save changes after configuring the FXO GateWay. -----------------------------------------------------------------------------------

-id PPPoE connection user name -pwd PPPoE connection password -reboot Reboot after remote host disconnection in PPPoE mode

usr/config$ ifaddr -sntp 1 10.1.1.1 While 10.1.1.1 stands for SNTP server’s IP address. -ipchange If the unit is behind the IP sharing device

PING 210.54.23.129: 56 data bytes no answer from 210.54.23.129 usr/config$ ping 192.168.4.121 PING 192.168.4.121: 56 data bytes 64 bytes from 192.168

-gwprefix Drop gateway prefix when call from IP (0=Keep, 1=Drop). -eod End of dial (0=Disable, 1=Enable). -ring T

level to determine who is master.) -gwprefix drop or keep gateway prefix . “0” means when gateway has incoming call from IP side, it will not drop p

Management Features: Two easy ways for system configuration - Console port: RS-232C port - TELNET - HTTP Brower (e.g. Internet Explorer) 1.3 Acces

4.2.11 [h323] Phone Book function allows users to define their own numbers, which mapping to real IP address. It is effective only in peer-to-peer m

-gkfind Gatekeeper finding port (1024~65535). -gkras Gatekeeper RAS port (1024~65535). -h225 H225 ras port (1024~65535).

define [prefix] in next command. Terminal type – device will register as H.323 defined Terminal, [prefix] command is not necessary. -dfgw default

this to recognize the called party. -gkid set GateKeeper name for GateKeeper discovery. When Gateway send out GateKeeper discovery message will sear

line -print Gateway line information. -config Set Gateway line information. hunt: Hunting group. hotline

automatically dial out “1001”. P2P Mode Usage: Set gateway under P2P mode. Create phone book table with “pbook ” command. Create a Hotline table wit

prefix -print prefix -add prefix 100 drop 1 insert 2000 prefix -add prefix 100 drop 1 prefix -add prefix 100 drop 0 ins

[-delete number] pbook -print Display phone book information and configuration. -add Add new phone book record.

sequence number as index. -add add a new record to phone book. When adding a record, users have to specify name, ip, and e164 number to complete th

[-volume line [voice level][input level][dtmf level]] [-nscng [G711U used1][G711A used2][G723 used3]] [-echo used][-mindelay t1][-

registered to Gatekeeper when it is set as Gatekeeper Mode. 2. LED flash means Dynamix DW-0002/H is not registered to Gatekeeper when it is set as G

-print print current voice information and configurations. -send define packet size for each codec. 20/40/60ms means to send a voice packet per 20/

usr/config$ voice –mindelay 90 –maxdelay 150 Note: be sure to know well the application before you change voice parameters because this might caus

Parameter Usages: -print print current settings in support command. -t38 to switch ON/OFF (1 = ON; 0 = OFF) T.38 fax ability. When T.38 ability is

=========================== 1 OK Ready 2 OK Ready 3 OK Ready 4 OK Ready usr/config$ 4.2.18 [

-ip Change the IP default rule.(1=FXO, 2=IP) -fxo Change the FXO default rule.(1=FXO, 2=IP) Example: route -add prefix

is to hunt between all ports in the same type. Usage Example: 1. route –add prefix 100 dst 1 e164 1001 min 1 max 3 hunt 1 This command means if gat

Tone1OFF . Tone2ON . Tone2OFF . Example: tone -print tone 1 480 620 1 1 5

[-modify index [passwd number][direction number]] [-delete index] fxopwd -print Display FXO password information and configurat

calling in FXO line of Gateway. ----------------------------------------------------------------------------------------------- usr/config$ recor

Please wait a moment... Write flash ok... Boot Rom : boot.104 Application Rom : 3804_0701.bin DSP App : 48302ce3.